Grey Acetal Fittings – PI Range
– Specifications
All our technical information for our Grey Acetal PI Range of products can be found here.
Grey Acetal Fittings – PI Range
Style and Description
For Liquids & Inert Gases
PI fittings offered in sizes 5/32″ to 5/8″ are manufactured in grey acetal copolymer, and fitted with a food grade Nitrile O-Ring, making them especially suitable for applications involving foodstuffs and potable liquids. They are however equally suitable for air and inert gases, and can be used on N2 /CO2 mixed gas dispense lines, pneumatic and vacuum applications. Ensure products are installed in accordance with local codes of practice.
Media / Application
✓ Potable Liquids
✓ Air / Vacuum
Sizes – Outside Diameter (OD) Pipe
- 5/32″ – 5/16″
- 3/8″ – 5/8″
Maximum Working Pressure (kPa)
| Temperature | Pressure | |
|---|---|---|
| AIR / VACUUM | 5/32″ – 5/16″ | 3/8″ – 5/8″ |
| -20°C | 1600kPa | 1000kPa |
| +1°C | 1600kPa | 1000kPa |
| +20°C | 1600kPa | 1000kPa |
| +65°C* | 1600kPa | 700kPa |
| Temperature | Pressure | |
|---|---|---|
| POTABLE LIQUIDS | 5/32″ – 5/16″ | 3/8″ – 5/8″ |
| -20°C | DO NOT FREEZE | |
| +1°C | 1600kPa | 1000kPa |
| +20°C | 1600kPa | 1000kPa |
| +65°C* | 1600kPa | 700kPa |
*NOT to exceed maximum temperature
Installation Instructions
Step 1
Prepare the Pipe
Ensure the pipe is free of score marks. Cut the pipe square. We recommend the use of JG Pipe Cutters.
To prevent damage to the O-Ring, remove all burrs and sharp edges. When connecting Speedfit Pipe, use a Speedfit Pipe Insert. A twisting motion will aid insertion. The insert should only be used with Speedfit Pipe.
Step 2
Push Up to Pipe Stop
Push the pipe into the fitting, to the pipe stop.
Step 3
Pull to Secure
Pull on the pipe to check it is secure. Test the system before use.
Don’t forget to push the pipe fully into the fitting, past both the collet (gripper) and the O-Ring.
Troubleshooting
Pipe Stop Distances
Stops are located at the following distances from the end of the fitting:
| Size | Stop Distances |
|---|---|
| 10mm | 20mm |
| 15mm | 30mm |
| 22mm | 35mm |
| 28mm | 44mm |
Check Pipe Grip & Depth
Make sure to push the pipe fully into the fitting, past both the collet (gripper) and the O-Ring.
Fitting may be gripped but not sealed if pipe is not fully inserted.
Do not use a hacksaw to cut the pipe.
This will leave unwanted burrs on the end of the pipe.
Do not use damage or scored pipe.
Score marks can cause leaks past the O-Ring.
How to Disconnect
Quick Disconnect
Push in Collet and Remove Tube
To disconnect, ensure the system is depressurized, push the collet square against the fitting. With the collet held in this position the tube can be removed.
Collet Covers & Clips
Collet Cover & Clip Applications
Use a collet cover or collet clip to provide added security against pipe disconnection, e.g. the fitting coming into contact with rigid surfaces and behind dry-lining walls.
Collet covers for use with standard Speedfit fittings, are available in white, red or blue to allow colour coding of pipes.
White & Grey Collet Clips
White or grey collet clips are used with standard fittings to prevent accidental pipe disconnection.
Red & Blue Collet Clips
Red or blue collet clips provide colour coding of pipe on Twist & Lock fittings. They are not designed to prevent accidental release, and should be fitted when the fitting is in the locked position.
Check out the products from family of brands
